Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD
US $43.20
Free Shipping

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

US$43.20

In Stock, ships within 1 business day
FREESHIPPING

CrazybeeX series flight controller is the first 4in1 AIO flight controller which could handle 2s.

The CrazybeeX DXS V1.0 is the newest member which is the first flight controller built-in DSM2/DSMX compatible SPI Receiver.

It’s a better upgrade for reduce the weight of your brushless whoop if you are using Spektrum transmitter. Best upgrade flight controller for Mobula6/Mobula6HD DSMX version .

Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S-2S battery input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky receiver support D8/D16
Built-in 5V 1A BEC
Built-in voltage detection
Firmware version Customized Betaflight4.3.0 S411
Onboard 4in1 ESC MCU upgraded to EFM8BB21
Power supply: 1-2S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7.HEX
Default protocol: DSHOT600
Onboard DSM2/DSMX SPI receiver SPI BUS receiver DSM2/DSMX compatible
Channels: Max 12ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
RSSI enable(show on the goggles)
Onboard 5.8g VTX Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V~5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready
Default vtx_power should set to be “3”
Onboard Voltage and Current detector Voltage Meter scale “110”
Amperage Mete scale “1175”

Notice: Recommend Betaflight configurator 10.7.0 version
SPI Receiver option: Spektrum

Bind procedure:

  1. Plug the USB then press the bind button, the red LED at the bottom of the flight controller will blinking fast , this indicate the SPI DSM2/DSMX receiver is in bind mode.
  2. Plug the USB then connect to Betaflight configurator, move to the CLI tab , then type “bind_rx”, the red LED at the bottom of the flight controller will blinking fast too , this indicate the SPI DSM2/DSMX receiver is in bind mode.

Package Included:

1* CrazybeeX DXS AIO 5in1 F4

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

Happymodel CrazybeeX DXS F4 1-2S AIO 5in1 Flight Controller Built-in VTX/ DSM2 DSMX Receiver/ESC/OSD

hitcounter